Four ceramic circuit carriers with patterned gold-colored and silver-colored metallization
Supplied circuit example. Material grade and process are not verified by the photograph.
Hypothetical worksheet inputResultQualification
4.00mm baseline ×1.30 assumed multiplier5.20mmNo altitude or standard assigned
5.80−0.20−0.15−0.10mm5.35mm minimum modeled separationIndependent worst-direction allowances assumed
5.35−5.20mm0.15mm comparison marginNot a compliance determination

Start with the operating environment of the assembly

A high-altitude clearance review begins with where the completed ceramic assembly will operate, not with the dielectric strength printed on a ceramic datasheet. Record the maximum operating altitude, enclosure arrangement, electrical interfaces and the product requirements used for the review. Distinguish operation from unpowered transport or storage, because the relevant conditions need not be the same. The creepage and clearance guide introduces the two geometric concepts. This article focuses on carrying an altitude requirement through the actual assembly geometry, dimensional tolerances and verification record so that a favorable bare-substrate drawing does not conceal an inadequate spacing elsewhere in the delivered product.

Separate the air path from the insulating surface path

Clearance follows a path through air, while creepage follows an insulating surface. Texas Instruments distinguishes these quantities in its isolation application note and emphasizes that component insulation characteristics do not automatically establish system compliance. For a ceramic assembly, draw both paths between the relevant conductive parts and identify which one each dimension represents. A longer route around a surface feature does not necessarily increase the direct air separation. Keep the two reviews connected but separate, using the applicable requirements for each. This prevents a proposed slot or ceramic extension from receiving credit for an air-gap improvement that the actual three-dimensional geometry does not provide.

Identify the governing requirements before selecting a factor

An altitude correction belongs to a defined insulation-coordination method and its scope. Infineon's TO-247 application note discusses clearance correction above two thousand meters within its cited framework. That is useful context, not authorization to apply one table to every ceramic product. Establish the applicable product standard, edition, insulation function and relevant environmental assumptions through the project's compliance process. Record where the baseline spacing and any correction came from. This article does not supply a universal clearance requirement. Its purpose is to make the calculation and geometry review reproducible after the responsible engineering team has established the requirements that apply to the intended product and market.

Create a node-pair register for the completed product

List the conductive parts that can form a relevant insulation boundary. Include circuit nodes, exposed terminals, cooling hardware, mounting hardware and nearby enclosure features as appropriate to the construction. Give each pair a stable identifier that can be used in drawings, calculations and inspection records. A single statement that the board supports a certain bus voltage leaves too much ambiguity about which path has been evaluated. For each pair, record the electrical conditions and insulation function assigned by the product design. Then connect that requirement to the actual nearest features in the assembly so the review can be repeated when a terminal, fastener or copper island changes.

Keep voltage quantities attached to their meaning

Working voltage, transient conditions and an insulation test voltage are not interchangeable inputs. Preserve the type and waveform associated with each electrical requirement rather than comparing only numerical magnitudes. A component that withstands a specified short test has not thereby established every continuous operating or spacing requirement for the system. Ask the circuit team to provide the conditions at the node pairs being reviewed, including the operating modes relevant to the application. Keep the evidence with the insulation worksheet. This makes it possible to see whether a spacing decision used the intended electrical condition or simply inherited a familiar number from another module with a different interface.

Show the correction arithmetic without implying a rating

For an invented arithmetic example, suppose a responsible design review has already established a baseline clearance of four millimeters and an applicable correction multiplier of 1.30 for a particular case. Their product is 5.20 millimeters. The multiplier in this example is hypothetical and is not assigned to an altitude or standard. The calculation illustrates how to keep the baseline, correction and resulting requirement visible. It does not establish a spacing rule for ceramic PCBs. In an actual worksheet, replace both assumed inputs with the approved values and their references, then compare the corrected requirement with the minimum realized assembly distance rather than with a nominal artwork dimension.

Compare required clearance with a tolerance-aware distance

Continue the invented example with a nominal assembly separation of 5.80 millimeters. Suppose the documented worst-direction dimensional allowances reduce that separation by 0.20 millimeters for conductor position, 0.15 for terminal position and 0.10 for assembly location. The remaining distance is 5.35 millimeters, leaving a nominal calculation margin of 0.15 millimeters against the assumed 5.20 requirement. This is a simple worst-direction stack, not a statistical tolerance model or proof of compliance. Check that the allowances describe distinct effects and do not double-count the same movement. Also confirm that this path remains the shortest one when the parts move within their permitted positions.

Inspect the nearest features in three dimensions

Top-view copper spacing is only one candidate path in a populated ceramic assembly. The closest conductive feature may be an elevated terminal, a bond, attachment material or hardware positioned above or below the substrate plane. Review a section or three-dimensional model for each important node pair. Identify which features are controlled by the substrate supplier and which are created by assembly. A generous ceramic outline does not resolve a short air gap between two projecting conductors. Preserve the critical path view with the drawing revision so an inspector or later designer can understand why the dimension was selected and which physical endpoints must remain controlled.

Do not treat bulk ceramic insulation as an air-gap substitute

Ceramic thickness and bulk dielectric behavior address a different physical barrier from an external clearance path. If a design changes from an air path to a solid-insulation arrangement, evaluate the new construction under the requirements that apply to that barrier. Do not use a high dielectric-strength value to justify shortening an unrelated air separation. Conversely, do not assume that increasing ceramic thickness necessarily lengthens the shortest external route. Mark the barrier type explicitly in the insulation register and review the complete geometry. This makes the design rationale clear when a material change is proposed primarily for thermal reasons but may also alter dimensions or interfaces relevant to insulation.

Review slots and grooves for the path they actually change

A groove can alter the route along a surface without moving the conductive endpoints farther apart through air. A cutout may change one path while creating another route around an edge or toward nearby hardware. Review the actual feature under the applicable measurement rules, including its dimensions and manufacturing tolerances. Avoid assigning a generic spacing credit solely because the drawing contains a slot. The substrate and assembly teams should agree which finished feature is required and how it will be verified. That agreement is particularly important when a geometric feature is small enough that tool radius, edge condition or positional variation changes the intended path.

Treat coatings and encapsulation as controlled constructions

If a proposal relies on a coating, gel or encapsulant to change the insulation arrangement, identify the relevant material, process and qualification evidence. The word coated is not a complete engineering specification. Define the covered region, thickness or other controlled characteristics required by the selected approach, and consider how the delivered construction will be verified. Keep any unprotected regions and interfaces visible in the review. This article does not assume that adding a coating eliminates altitude-related questions or converts every gap into qualified solid insulation. Those conclusions need evidence for the actual product construction and the applicable requirements, rather than a general property statement about the coating material.

Include the enclosure and pressure environment in the evidence

A claim about a sealed or controlled-pressure enclosure should be connected to the operating conditions it actually maintains. Record the boundary relied upon and the product states covered by that claim. Do not assume that an enclosure changes the internal pressure merely because it prevents ordinary handling access. If the design depends on a particular internal environment, the system assessment must establish how that environment is maintained and verified throughout the intended operation. Keep this responsibility explicit between the module and equipment teams. Otherwise the ceramic assembly may be designed around an environmental assumption that the final housing was never specified or tested to provide.

Choose verification methods that answer distinct questions

Dimensional inspection can establish a physical separation, while electrical testing addresses the behavior covered by the specified test conditions. Neither automatically replaces the other. Define the inspection endpoints and the delivered state in which dimensions are checked. Separately identify the electrical tests required by the applicable product assessment, their conditions and acceptance criteria. If reduced-pressure testing is part of the agreed verification, tie its conditions to the intended claim and retain the configuration of the tested assembly. Avoid describing a room-condition withstand result as proof of performance in every altitude environment. The evidence should show precisely which geometric and electrical requirements have been checked.

Maintain the spacing through assembly and service variation

The minimum distance can depend on component placement, attachment material, fastener position and the way the module is installed in its equipment. Review these variations with the same attention given to copper fabrication tolerance. Include any permitted service replacement or adjustment that can change the nearest conductive features. The mechanical mounting guide provides related support and interface considerations. If installation controls are essential to maintaining the required clearance, make them part of the controlled product documentation and verification process. A dimension that exists only in a nominal model is not an adequate description of a product assembled from toleranced parts.

Control changes using the node-pair record

When a design changes, use the node-pair register to identify which paths need reassessment. A different terminal shape, cooling plate, fastener or encapsulation process may affect the insulation review even when the ceramic material remains unchanged. Record the revised geometry and the assumptions used in the new comparison. Keep the old and new evidence distinguishable so a previously accepted configuration does not silently lend its status to a modified assembly. This approach also helps purchasing evaluate substitutions: a replacement part with the same electrical function may have a different physical envelope or mounting tolerance that changes the spacing to surrounding conductive features.

Release a review that another engineer can reproduce

The completed clearance review should identify the intended environment, applicable requirement sources, node pairs, voltage conditions, barrier types, correction method and minimum realized dimensions. Include critical path views, tolerance assumptions and the inspection or test records supporting the conclusion. Separate unresolved inputs from verified results so the project can close them explicitly before relying on the design. The value of the review is its traceability from requirement to physical assembly. For high-altitude ceramic electronics, that traceability prevents strong bulk material properties or a familiar nominal gap from being mistaken for evidence that every relevant air path in the completed product has been assessed.

Engineering example

The multiplier and dimensions are invented solely to demonstrate worksheet arithmetic. Applicable product requirements must establish actual distances and test conditions.

Before you release the design

  • Define the operating environment and governing requirements.
  • Register node pairs and barrier types.
  • Separate air and surface paths.
  • Review the shortest three-dimensional path with tolerances.
  • Retain configuration-specific inspection and test evidence.

Sources and further technical reading

Manufacturer references support the material and process context. Worked examples and checklists are engineering guidance; they are not test results or supplier guarantees.

  1. Texas Instruments — SDAA268,June2026; insulation quantities and component-versus-system requirements
  2. Infineon — AN2021-09,Improved TO-247 package; clearance and altitude context